The article begins with an emphasis: plant protection is risky, choose to be cautious! Private self-assembled plant protection drones without drone experience are not recommended. Assembling a drone requires a three-point technique. Seven points of care, welding and commissioning are two major points. You need to have enough skill and care to make a positive result. I hope that you will be a young man, get this cheat, practice carefully, and install Dafa as soon as possible.
1. Material preparation
Bill of materials:
1. Rack: EFT six-axis 10kg rack
2. Power system: 6 of 8010 motors, 3 pairs of good surplus 80A ESC, 24 inch folding paddles
3. Sprinkler system: 1 pump, 1 step-down ESC, 4 pressure nozzles, water pipes and adapters
4. Flight control: Dajiang A3 (installation reference)
5. Plug accessories: AS150 anti-fire male red and black 2 pairs, XT90 male 6 , XT60 male and female head 1 pair, 4.0mm banana head male and female 18 pairs, 5mm heat shrinkable tube 1 m, 10mm heat shrinkable tube 1 Meter, 8mm snake skin network tube 4 meters
6. Tools: a set of hexagonal screwdrivers, 1 soldering station above 150W, 1 hot air gun
2, the installation rack
The racks are modular and have been assembled for most of the internal assembly, so the overall installation is relatively simple. The factory comes with instructions and can be assembled according to the instructions.
It should be noted that before installing the rack, it is recommended to first solder the power cord plug at the bottom of the center board for the next step, so as not to facilitate the soldering of the bottom plug after the whole machine is assembled.
(Follow the "Wing Feite UAV " public number, reply "welding", you can get the power cord plug welding tutorial)
Before the whole machine is assembled as shown in the above figure, the main power plug is welded and then the frame is assembled. The installation process is shown in the following figure:
3, motor, ESC pretreatment
Before the whole machine is assembled as shown in the above figure, the main power plug is welded and then the frame is assembled. The installation process is shown in the following figure:
Electric adjustable female
1. Material preparation
Bill of materials:
1. Rack: EFT six-axis 10kg rack
2. Power system: 6 of 8010 motors, 3 pairs of good surplus 80A ESC, 24 inch folding paddles
3. Sprinkler system: 1 pump, 1 step-down ESC, 4 pressure nozzles, water pipes and adapters
4. Flight control: Dajiang A3 (installation reference)
5. Plug accessories: AS150 anti-fire male red and black 2 pairs, XT90 male 6 , XT60 male and female head 1 pair, 4.0mm banana head male and female 18 pairs, 5mm heat shrinkable tube 1 m, 10mm heat shrinkable tube 1 Meter, 8mm snake skin network tube 4 meters
6. Tools: a set of hexagonal screwdrivers, 1 soldering station above 150W, 1 hot air gun
2, the installation rack
The racks are modular and have been assembled for most of the internal assembly, so the overall installation is relatively simple. The factory comes with instructions and can be assembled according to the instructions.
It should be noted that before installing the rack, it is recommended to first solder the power cord plug at the bottom of the center board for the next step, so as not to facilitate the soldering of the bottom plug after the whole machine is assembled.
(Follow the "Wing Feite UAV " public number, reply "welding", you can get the power cord plug welding tutorial)
Before the whole machine is assembled as shown in the above figure, the main power plug is welded and then the frame is assembled. The installation process is shown in the following figure:
3, motor, ESC pretreatment
Before the whole machine is assembled as shown in the above figure, the main power plug is welded and then the frame is assembled. The installation process is shown in the following figure:
Electric adjustable female
Power Bank,Mobile Power Bank,Charging Power Bank,Fast Charging Flat Power Banks
Guangzhou Lufeng Electronic Technology Co. , Ltd. , https://www.lufengelectronics.com